







Free written scope consultation - allowances, timeline, and change-order rules on paper before a single trade is scheduled
Schluter Driveway & Pavers: The Sunnyvale Owner’s Guide
If a Schluter paver edge profile or drainage channel on your driveway has cracked, loosened, or pulled away from the pavement, we replace it and re-set the surrounding surface for a typical installed cost of $500-$2,200 depending on linear footage and whether the setting bed needs rebuilding. On a full paver driveway, installation runs $7,000-$18,000. We’re Penhallow Remodeling Sunnyvale, an independent remodeling company that is not affiliated with Schluter, and we can usually get a written quote to you within a day or two of your call.
Most Sunnyvale owners find out something’s wrong the same way: a paver edge in the driveway starts rocking underfoot, a strip of pavers along the garage apron sinks after a wet winter, or the metal Schluter trim that holds a border course has lifted and is now a trip edge. That lifting trim is often the first sign the bedding underneath has shifted, not the trim itself.
Which Schluter Models This Applies To

Schluter’s paver and driveway edge lines are matched to the thickness of the paving surface, and that’s the first thing we check. The profiles are sized to the paver or tile depth – roughly in the 20mm to 30mm-plus range for a standard driveway paver – and a profile built for a thin porcelain paver won’t hold a thick concrete paver correctly. Get the depth wrong and the edge looks fine on day one, then works loose under vehicle load. We measure the actual paver thickness and match the profile to it rather than eyeballing a replacement.
To identify what you have, look on the visible face of the trim for a stamped series name, and measure the profile’s overall depth and the paver it sits against. If the label is worn off, a photo with a tape measure across the profile gives us enough to match it.
On the OEM-versus-aftermarket question: for Schluter specifically, we source the matching Schluter profile whenever the existing system is Schluter and the geometry allows it, because a mismatched substitute often means the anchoring leg doesn’t line up the same way. An aftermarket edge can work fine on a fresh install, but on a repair where you’re reusing the existing bed and border, matching the original profile is what keeps the joint tight. We won’t promise a specific part is on a shelf – parts are sourced to your job – so we confirm the exact model before quoting labor.
Styles & brands we work with
- Kitchen remodeling
- Bathroom remodeling
- Home additions & ADU
- Roofing
- Windows & doors
- Driveway & pavers
- Fence
Signs Your Schluter Driveway & Pavers Is Failing
Here’s what a failing edge profile or drainage channel looks like in practice, and what’s usually behind it:
- Paver edge rocking underfoot. The profile’s anchoring leg has lost grip in the bedding, often because the base under the edge wasn’t compacted enough when it was set. Movement at the edge is the early warning.
- Trim lifting along the garage apron. Water running off the slab gets under the edge and freezes or expands, pushing the profile up. In Sunnyvale’s wet winters we see this most on driveways that pitch toward the house.
- Visible cracks in the profile or channel. Usually impact damage from a wheel or a loaded cart, or a profile sized too thin for the paver it’s meant to hold.
- Paver border course shifting out of line. The edge restraint is no longer doing its job, so the outer pavers creep. Left alone, the shift spreads inward a course at a time.
- Standing water at a drainage channel. Sediment and grit have clogged the channel or the pitch has settled. A channel that no longer drains is a profile that’s no longer seated correctly.
California’s dry summers and wet winters are hard on any edge detail. The ground swells and shrinks, and a marginal bedding job shows its weakness by the second or third rainy season rather than the first.
See the difference
Before
After
Before
After
Before
AfterReplacement Cost & What’s Included

Replacing the failed profile and re-setting the border on a Sunnyvale driveway typically runs $500-$2,200 installed, with the range driven by linear footage, how much of the setting bed has to be rebuilt, and whether a drainage channel needs re-pitching. If the failure has undermined a larger section of pavers, we may recommend re-laying that run – a full paver driveway installation is $7,000-$18,000, and a paver patio is $3,500-$11,000 if the same problem shows up out back.
Every quote is a written line-item number before any work starts: the Schluter-compatible profile, the bedding and setting materials, labor, and cleanup, each on its own line. The number on day one is the number on the invoice. The work carries our written guarantee, plus the 365-Day Done Right Promise – if the repair fails inside a year, we come back and fix it at no charge, and a failed repair gets a free return visit with no service-call fee.
DIY or Call Us?
You can safely check a few things yourself: photograph the profile with a tape measure across it, note where it’s lifting or rocking, and clear grit from a clogged channel so you can see how it drains. What we don’t recommend is prying up pavers to reset the edge on your own. The anchoring leg is set into a compacted bedding that has to be re-done to the right depth and pitch, and a paver border that isn’t re-seated properly just fails again after the next wet season – which is the exact repair-that-cracked-six-weeks-later story owners come to us trying to avoid. Getting the base and pitch right the first time is the whole job.
Our technicians have up to 22 years of experience with edging, paving, and drainage details, and a live person answers the phone around the clock – call (888) 426-8719 to talk through what you’re seeing.
FAQs

A properly installed profile should hold for the life of the paving around it – many years – while one set on an under-compacted bed often starts moving within a couple of seasons. Sunnyvale’s wet winters speed that up, so getting the bedding right matters more than the trim itself. Call (888) 426-8719 for an exact quote on a replacement – estimates are free.
Sometimes yes – if the profile is intact and only the bedding under it has settled, we can re-seat it. If the profile is cracked or sized wrong for the paver, replacing it is the honest fix. We’ll tell you which after looking. Call (888) 426-8719 and we’ll get a written number to you.
A localized edge replacement is usually a single-day job, while a larger re-lay of the border or a re-pitched drainage channel can run into a second day. We give you a real arrival window and stick to it – no vague all-day windows, no surprises. Call (888) 426-8719 to schedule your free estimate.
We match the profile to your actual paver thickness and the series stamped on the trim, then confirm the exact model before quoting – and we source it to your job rather than promising it sits on a shelf. Background-checked, uniformed technicians handle the install. Call (888) 426-8719 and we’ll walk you through it.
Whether it’s a lifting edge profile or a paver border that’s crept out of line, the fix starts with a written number you can hold us to. We also work with KraftMaid, Cambria, and Silestone on the interior side of the home when a remodel brings us inside. Call Penhallow Remodeling Sunnyvale at (888) 426-8719 for a free estimate – a live person will pick up, and we’ll set a real arrival window and stand behind the work in writing.
Written by the team at Penhallow Remodeling Sunnyvale, serving Sunnyvale and nearby areas.












